Crystalline phase of TiO2 nanotube arrays on Ti–35Nb–4Zr alloy: Surface roughness,electrochemical behavior and cellular response

An investigation was made into the electrochemical, structural and biological properties of self-organized amorphous and anatase/rutile titanium dioxide (TiO₂) nanotubes deposited on Ti–35Nb–4Zr alloy through anodization-induced surface modification. The surface of as-anodized and heat-treated TiO₂ nanotubes was analyzed by field emission scanning electron microscopy (FE-SEM), revealing morphological parameters such as tube diameter, wall thickness and cross-sectional length. Glancing angle X-ray diffraction (GAXRD) was employed to identify the structural phases of titanium dioxide, while atomic force microscopy (AFM) was used to measure surface roughness associated with cell interaction properties. The electrochemical stability of TiO₂ was examined by electrochemical impedance spectroscopy (EIS) and the results obtained were correlated with the microstructural characterization. The in vitro bioactivity of as-anodized and crystallized TiO₂ nanotubes was also analyzed as a function of the presence of different TiO₂ polymorphic phases. The results indicated that anatase TiO₂ showed higher surface corrosion resistance and greater cell viability than amorphous TiO₂, confirming that TiO₂ nanotube crystallization plays an important role in the material's electrochemical behavior and biocompatibility.     

大豆蛋白纳米纤维对铁纳米颗粒的稳态化作用

为明确大豆蛋白纳米纤维的结构形成和扩宽铁强化剂的食品工业应用，以大豆分离蛋白（soy protein isolate，SPI）为原料，通过5 h的酸热处理制备纳米纤维（soy protein isolate fibrils，Fib SPI），系统研究纤维形成前后蛋白结构的变化，并进一步制备铁纳米颗粒（iron nanoparticles，Fe NPs），探究Fib SPI对铁的稳态化作用。研究结果表明：在酸热处理过程中，SPI产生大量的β-折叠结构，其与硫磺素T结合，显示出增强的荧光强度；此外，7S组分先发生降解，利于纤维成核形成，随后11S逐渐被水解，促进纤维生长；同时水解产生大量的小肽组分，提高了产物的还原力。研究进一步利用Fib SPI递送铁纳米颗粒（Fe NPs），发现与原始SPI相比，铁纳米颗粒可在Fib SPI原位形成胶体稳定的铁-大豆蛋白纳米纤维复合物（Fe FibSPI），并以Fe（II）形式存在，其对乳液体系色泽及稳定性的影响较硫酸亚铁或氯化铁小。该研究可为构建新型植物基铁强化剂递送体系提供理论和方法指导。     

双对苯醌的抗氧化活性分析及其固体发酵条件优化

为探索生物活性未知的双对苯醌（2,7-dihydroxy-3,6,9-trimethyl-9H-xanthene-1,4,5,8-tetraone，DTXT）的抗氧化活性，并提高其发酵产量，考察DTXT的还原力以及对超氧阴离子自由基、羟自由基、1,1-二苯基-2-三硝基苯肼（1,1-diphenyl-2-picrylhydrazyl，DPPH）自由基的清除效果，在单因素试验基础上，采用响应面法优化了DTXT产生菌瓶生顶孢霉（Acremonium cavaraeanum）CA022菌株的固体发酵培养基。结果表明：在200 μg/mL质量浓度下，DTXT的还原力与芦丁差异不显著，高于VE和2,6-二叔丁基-4甲基苯酚，对超氧阴离子自由基清除率达到67.00%，对羟自由基清除率达到78.83%，对DPPH自由基清除率达到76.53%。通过响应面试验，得到最佳培养基配方为葡萄糖0.773%、硝酸钠0.185%、H3BO3 0.032%、VB1 100 μg/100 g，在此条件下实际获得的DTXT产量为4 150.8 mg/kg，是优化前产量的（2 864.83 mg/kg）1.45 倍。     

Experimental study on mitigating wind erosion of calcareous desert sand using spray method for microbially induced calcium carbonate precipitation

Wind erosion is one of the significant natural calamities worldwide, which degrades around one-third of global land. The eroded and suspended soil particles in the environment may cause health hazards, i.e. allergies and respiratory diseases, due to the presence of harmful contaminants, bacteria, and pollens. The present study evaluates the feasibility of microbially induced calcium carbonate precipitation (MICP) technique to mitigate wind-induced erosion of calcareous desert sand (Thar desert of Rajasthan province in India). The temperature during biotreatment was kept at 36 °C to stimulate the average temperature of the Thar desert. The spray method was used for bioaugmentation of Sporosarcina (S.) pasteurii and further treatment using chemical solutions. The chemical solution of 0.25 pore volume was sprayed continuously up to 5 d, 10 d, 15 d, and 20 d, using two different concentration ratios of urea and calcium chloride dihydrate viz 2:1 and 1:1. The biotreated samples were subjected to erosion testing (in the wind tunnel) at different wind speeds of 10 m/s, 20 m/s, and 30 m/s. The unconfined compressive strength of the biocemented crust was measured using a pocket penetrometer. The variation in calcite precipitation and microstructure (including the presence of crystalline minerals) of untreated as well as biotreated sand samples were determined through calcimeter, scanning electron microscope (SEM), and energy-dispersive X-ray spectroscope (EDX). The results demonstrated that the erosion of untreated sand increases with an increase in wind speeds. When compared to untreated sand, a lower erosion was observed in all biocemented sand samples, irrespective of treatment condition and wind speed. It was observed that the sample treated with 1:1 cementation solution for up to 5 d, was found to effectively resist erosion at a wind speed of 10 m/s. Moreover, a significant erosion resistance was ascertained in 15 d and 20 d treated samples at higher wind speeds. The calcite content percentage, thickness of crust, bulk density, and surface strength of biocemented sand were enhanced with the increase in treatment duration. The 1:1 concentration ratio of cementation solution was found effective in improving crust thickness and surface strength as compared to 2:1 concentration ratio of cementation solution. The calcite crystals formation was observed in SEM analysis and calcium peaks were observed in EDX analysis for biotreated sand.     

物料堆场智能化管理经验分享

华润水泥（罗定）有限公司根据物料储存需求，共有三个长堆棚分为9个室内料场堆放原材料及混合材，厂内有4台铲车无规则轮流在这8个料场内作业，同时外来运料货车、公司化验及验收人员也会不间断地进入不同堆棚。由于料场内空间狭窄，驾驶员视线不好，如果堆棚料场内铲车在作业时，有其他人员或车辆进入铲车工作区域共同作业，在没有检测装置对进入的人、车进行识别，提醒铲车驾驶员的情况下，容易发生碾压进入人员或车辆碰撞的安全事故。公司根据现场实际，自2020年起决定实施从堆场出入口智能红外感应技术、装载机车载识别系统、智能声光语音提醒、实时监控显示、照明、堆场硬件设施等五方面实施物料堆场车辆智能化安全预警系统项目。     

低压静电场辅助冷冻对竹笋品质的影响

为研究低压静电场辅助冷冻对竹笋冻结特性的影响，以冻结曲线、硬度、水分损失率、水分迁移、冰晶形态和组织微观结构为指标，探究低压静电场辅助冷冻（－35 ℃）和普通冷冻（－35 ℃）条件下竹笋品质的变化规律。结果表明：低压静电场辅助冷冻提高了冻结效率，改变了冰晶形态及分布，减轻了组织微观结构破损程度，改善了解冻汁液流失情况。与静电板间距10、20、30、40 cm处的冷冻竹笋解冻后水分损失率分别为14.16%、12.58%、9.73%、10.44%，显著低于对照组（21.01%）（P＜0.05），硬度分别为461.19、507.48、496.65 g和455.31 g，显著高于对照组（350.70 g）（P＜0.05）。低场核磁共振分析结果表明，在低压静电场辅助冷冻下竹笋解冻后汁液流失减少，扫描电子显微镜观察结果显示，竹笋纤维排列整齐，组织微观结构保持较好。低压静电场辅助冷冻可有效改善竹笋品质，可为利用低压静电场进行果蔬的冷冻贮藏和冷链运输提供参考。     

Designing amorphous formulations of polyphenols with naringin by spray-drying for enhanced solubility and permeability

Naringin (NAR), a major flavanone (FVA) glycoside, is a component of food mainly obtained from grapefruit. We used NAR as a food additive to improve the solubility and permeability of hydrophobic polyphenols used as supplements in the food industry. The spray-dried particles (SDPs) of NAR alone show an amorphous state with a glass transition temperature (T_g) at 93.2 °C. SDPs of hydrophobic polyphenols, such as flavone (FVO), quercetin (QCT), naringenin (NRG), and resveratrol (RVT) were prepared by adding varying amounts of NAR. All SDPs of hydrophobic polyphenols with added NAR were in an amorphous state with a single T_g, but SDPs of hydrophobic polyphenols without added NAR showed diffraction peaks derived from each crystal. The SDPs with NAR could keep an amorphous state after storage at a high humidity condition for one month, except for SDPs of RVT/NAR. SDPs with NAR enhanced the solubility of hydrophobic polyphenols, especially NRG solubility, which was enhanced more than 9 times compared to NRG crystal. The enhanced solubility resulted in the increased membrane permeability of NRG. The antioxidant effect of the hydrophobic NRG was also enhanced by the synergetic effect of NAR. The findings demonstrated that NAR could be used as a food additive to enhance the solubility and membrane permeability of hydrophobic polyphenols.     

The formed surface characteristics of SiCf/SiC composite in the nanosecond pulsed laser ablation

For the advantages of high-temperature resistance, corrosion resistance and ultra-high hardness, SiC_f/SiC composite is becoming a preferred material for manufacturing aero-engine parts. However, the anisotropy and heterogeneity bring great challenges to the processing technology. In this study, a nanosecond pulsed laser is applied to process SiC_f/SiC composite, where the influence of the scanning speed and laser scanning direction to the SiC fibers on the morphology of ablated grooves is investigated. The surface characteristics after ablation and the involved chemical reaction of SiC_f/SiC are explored. The results show that the increased laser scanning speed, accompanied by the decreasing spot overlap rate, leads to the less accumulation of energy on the material surface, so the ablation effect drops. In addition, for the anisotropy of the SiC_f/SiC material, the obtained surface characteristics are closely dependent on the laser scanning direction to the SiC fibers, resulting in different groove morphology. The element composition and phase analysis of the machined surface indicate that the main deposited product is SiO₂ and the carbon substance. The results can provide preliminary technical support for controlling the machining quality of ceramic matrix composites.     

基于气相色谱-离子迁移色谱分析不同贮藏方式对洋葱浆馕风味的影响

采用气相色谱-离子迁移谱（gas chromatography-ion mobility spectrometry，GC-IMS）对洋葱浆馕6 种不同贮藏条件下挥发性物质进行分析，包括低温贮藏、室温贮藏、真空贮藏、脱氧贮藏、保鲜剂贮藏和保鲜剂结合脱氧贮藏。研究表明：在洋葱浆馕中共鉴定出66 种挥发性风味物质，其中包括醇类9 种、酮类4 种、醛类18 种、酯类4 种、呋喃衍生物3 种，酸类1 种和未能识别的化合物27 种。随着贮藏时间的延长，低温贮藏和真空贮藏洋葱浆馕在贮藏期内醛类挥发性有机物基本不变，其他处理组的醛类挥发性有机物在贮藏期内变化呈降低的趋势。结合主成分分析和欧氏距离可以发现低温贮藏和其他贮藏方式的第0天挥发性物质种类和浓度较为接近，主成分分析图中点的位置也相聚在一起，说明低温贮藏馕的挥发性物质变化不明显。该研究建立不同贮藏方式洋葱浆馕挥发性气味指纹图谱，可视化出洋葱浆馕挥发性成分轮廓，为洋葱浆馕贮藏期间风味变化规律提供信息。     

Ni-based catalysts with coke resistance enhance by radio frequency discharge plasma for CH4/CO2 reforming

Coke deposition has been considered to be one of the most important reasons hindering the stability of the catalyst during CH₄/CO₂ reforming. In this study, after the addition of P123 (PEG-PPG-PEG triblock copolymer), Ni²⁺ can be well-dispersed on the mesoporous molecular sieve MCM-41. And then, the catalysts were prepared by using N₂ radio frequency (RF) discharge plasma for different treatment times to reduce the size of Ni particles, improve the anti-coking performance, and thereby improve the stability of the catalyst. The results showed that the catalyst NM-P123-PN2h exhibits superior catalytic properties in the CH₄/CO₂ reforming. The initial conversions of CH₄ and CO₂ were 90.80% and 89.60% at 750 °C, respectively. The catalyst NM-P123-PN2h showed highly coke resistance with less carbon deposition (1.12%) at 750 °C after 10 h of continuous reaction, while the carbon deposition of the catalyst NM-C was 37.32%. Compared with the traditional calcination method, the catalyst prepared by plasma treatment has a smaller particle size and better dispersibility of nickel. In particular, the nickel particle size of the catalyst NM-C was 8.37 nm, however, that of the catalyst NM-P123-PN2h was only 1.70 nm, and the nickel particle size was reduced by 5 times. Therefore, it can be concluded that the catalyst prepared under the combined action of P123 and RF plasma-treated can effectively improve the coke resistance of the catalyst and the stability of the CH₄/CO₂ reforming.